Scale 4x4 R/C Forums

Scale 4x4 R/C Forums (https://www.scale4x4rc.org/forums/index.php)
-   Tips, Tricks, FAQ's (https://www.scale4x4rc.org/forums/forumdisplay.php?f=16)
-   -   clod axles to Dualhunter gearbox? (https://www.scale4x4rc.org/forums/showthread.php?t=72313)

adjun 01-22-2013 05:12 PM

clod axles to Dualhunter gearbox?
 
Noob question:
I was wondering if Clod axels are compatible with a Dualhunter gearbox. Please give details or whats the best way to achieve this disaster.
Thanks.

Goals-lower gear ratio for higher speeds.
Items-complete Clod gearbox and axles, complete Dualhunter gearbox-NO axles

Wheelyking4x4x4 01-23-2013 01:29 AM

Not possible - Clodbuster uses a motor/gearbox/solid axle setup, and the dual hunter is essentially the same but with independent suspension no actual gearbox or axle
Clodbuster

Dual hunter


what are you trying to make? a faster dual hunter or a faster clodbuster? best bet is to go for faster motors, however if you want speed i would recommend hpi or traxxas, tamiya plastic (particularly clods) is not very forgiving

adjun 01-23-2013 02:42 AM

faster Clod. Dual hunter would be the donor parts. Both of these chassises were pitched.
Clod's axle spline looks way larger too.

Wheelyking4x4x4 01-23-2013 02:13 PM

From what i've seen most guys just go to 2 brushless motors, check out rcmt.net thats where most of the racing clods are :nice:

adjun 01-23-2013 04:07 PM

I've heard about going brushless. I trying to keep this a budget build. I think I'm gonna get some new doggones and jerry-rig the Dualhunter gearbox.
I have plenty of stainless material to use.

rcmt.net hasn't fully activated it. That's where I'm having problems with my account.

Wheelyking4x4x4 01-25-2013 12:30 AM

You can also get adjustable motor mounts for the clodbuster, so you can use a bigger pinion and get a bit of speed that way

BADMUTHATrUCKER 01-25-2013 01:34 AM

I think I see what you want to do, and no. The Clod axles are 6mm, and the WD-01 diff side gears are 5mm splined.

You can get adjustable Clod motor plates that will let you gear for more speed.

adjun 01-25-2013 01:57 AM

im just gonna rig the Dualhunter gearbox. got stainless steel to configure the chassis and new doggones.
Thanks for all the insight. Build is going rough. I was thing of using the Clod 4's suspension rod but there was a bit of binding b/c of the WD-01's longer gearbox. I'm just gonna rigid mount it on the Clod4's chassis.

adjun 02-13-2013 07:08 PM

50mm wider than stock Clod
 
Started on the chassis today. hammer and dolley made the (stainless) center plate a tighter fit.
All handmade with angle grinder, sand paper, dremel, and a hammer.


cut the original bottom plate in half to attach the stainless lower part but more holes to drill.

You can see how more wider it is than stock.

adjun 03-13-2013 07:45 PM

I gave up on this build because I got another Tamiya chassis.

alicezii1 08-15-2016 08:35 AM

Thx for the info^_^
ดูตารางบอลวันนี้


All times are GMT -6. The time now is 11:44 PM.

Powered by vBulletin®
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright 2004 - 2020, Scale 4x4 R/C